Star Micronics TSP143IIIW (Wi-fi) receipt printer

Requirements

To use this hardware with your Shopify store, you need to meet the following requirements:

  • the Shopify POS app
  • a compatible iPad that is running iOS 15 or higher, an iPhone that is running iOS 15 or higher, or a compatible Android device that is running version 10 or higher

Where to buy the TSP143IIIW Wi-fi receipt printer

The Star Micronics TSP143IIIW Wi-fi receipt printer is available from the Shopify Hardware Store in supported countries.

Buy printer paper

Any thermal paper rolls with the following dimensions work with the printer:

  • width is 3 1/8" (80mm)
  • length is no more than 230 feet (70m)

For an explanation of how to load the receipt printer, refer to the guide in the manufacturer's hardware manual.

Plug in your Wi-Fi printer

Connect your printer to the power supply.

Steps:

  1. Plug one end of the power cable into the back of your receipt printer.
  2. Plug the other end of the cable into a power outlet and turn the printer on.

If paper is loaded, then a diagnostic report prints.

Installation and setup

  1. Connect your printer to the power supply.
  2. If your printer has already been set up for another Wi-Fi network, then initialize the printer's network settings. Ensure that your printer and the POS device are both on a 2.4 GHz network. The printer can only connect to a 2.4 GHz network.
  3. In the Shopify POS app, tap More > Settings > Set up hardware.
  4. Tap Receipt printer > Star Micronics > Wi-Fi.
  5. Tap Allow location access.
  6. Tap to allow Shopify POS to use your location.
  7. Make sure your printer is turned on and tap Next step.
  8. Make sure you have loaded paper into the printer and tap Next step.
  9. In your iPad's Wi-Fi settings, connect to the receipt printer.
  10. Return to the Shopify POS app and log back into the app. When Shopify POS has found the printer, tap Complete Wi-Fi details. If this option isn't displayed, then you might need to repeat steps 1 to 11.
  11. Tap Select to choose the type of network security that your Wi-Fi network uses and then tap Save.
  12. Enter the password for your Wi-Fi network and then tap Done.
  13. Tap Connect and then Done.

Confirm that your printer displays as connected under Receipt Printers.

After connecting your printer, don't forget to:

Initialize the printer network settings

If you want to connect your printer to a new Wi-Fi network, then initialize the printer's network settings.

When you initialize your printer, the settings are reverted to their defaults. You need to reconfigure the settings that you use, such as the wireless and password settings.

Steps:

  1. Turn the printer off.
  2. Press and hold the RST button at the same time that you turn the printer on.
  3. Hold the RST button until the printer resets twice. When the device resets, it makes an internal operation noise.
  4. Turn the printer off.

Troubleshooting your TSP143IIIW printer

If your TSP143IIIW printer stops working, follow these steps to troubleshoot your printer:

  1. Make sure that your printer's Wi-Fi connection is set up correctly.
  2. Confirm that you are connected to the internet. Your printer requires an internet signal to run properly.
  3. Confirm that your printer displays on the Hardware screen in the Shopify POS app. If the printer is improperly connected, then it displays on the settings screen or it displays as "Disconnected".
  4. Try turning your printer off and then on. This restarts your printer and usually fixes any issue on the printer's end.
  5. If the previous steps haven't resolved your issue, then debug your printer:
    1. Turn your printer off and press and hold the FEED button. At the same time, and still holding the FEED button, turn the printer back on.
    2. Let the printer print off the firmware information and then let go of the feed button. The printer tries to connect to the internet and then continue to print off more diagnostic information. Review the following troubleshooting steps that match the error text displayed:
    3. The IP address under "Current IP Parameters Status" displays zeroes: First, turn off the printer, wait five seconds, and then turn it back on. Try the debug process again. If that doesn't work, then confirm that you've followed the printer installation and setup instructions. Make sure that your printer is plugged in and connected to your wireless network. Finally, if none of the above solutions work, contact your internet provider. It could be a problem with your internet setup.
    4. I see a "No Host Connection" message: This usually happens when you lose your internet connection or when your printer isn't connected to your router properly. Check your internet signal and wireless router.

If the ERROR indicator is blinking red

This is caused when there is no paper present in the printer. Open the printer, replace the paper, and close the lid. The ERROR indicator should turn off and the READY indicator should come on.

Paper jams

If you feed the paper into the receipt printer at an angle, then a paper jam is likely to happen. If this happens, then turn off the printer, open it up, and feed the paper in again.

If you are trying to make your receipt narrower than the specified 3 inch width, then make sure you use the divider provided. Don't fold the paper when you feed it into the printer.

Customize receipts

You can customize both the basic receipt layout and the transaction description.

Limitations when using the Star Micronics TSP100IIIW (Wi-fi) receipt printer

Shopify POS won't work with multiple TSP100IIIW (Wi-fi) receipt printers at the same time.

Can’t find the answers you’re looking for? We’re here to help.