Socket Mobile 1D barcode scanner

You can use the Socket Mobile S700 or CHS 7Ci barcode scanner to scan both digital and printed 1D barcodes.

Shopify POS - Socket Mobile barcode scanner

The Socket Mobile S700 and CHS 7Ci are lightweight, portable barcode scanners that connect wirelessly to Shopify POS.

Who is the 1D barcode scanner for?

You should use the Socket Mobile S700 or CHS 7Ci 1D barcode scanners if you want to add products to the Shopify POS cart quickly without browsing your catalog to find them.

The scanner connects wirelessly to Shopify POS with Bluetooth, so you can use the scanner at markets, fairs, popup locations, or a physical store. It's charged by plugging the included charging cable or cradle into a power socket. When fully charged, the scanner's battery lasts for up to 14 hours (about 15,000 scans).

Compatible devices and models

This table shows which Socket Mobile 1D scanners are compatible with Shopify POS:

Socket Mobile 1D scanners compatible with Shopify POS
Compatible POS devices Compatible Socket Mobile S700 SKUs Compatible Socket Mobile CHS 7Ci SKUs
iPad
  • CX3360‑1682
  • CX3397‑1855
  • CX2870‑1409
  • CX2895‑1508
  • CX2885‑1484
  • CX2883‑1480
  • CX2887‑1486

Where to buy the Socket Mobile 1D barcode scanner

You can buy the Socket Mobile 1D barcode scanner from the following suppliers:

Suppliers for the Socket Mobile 1D barcode scanner
Region Reseller
Canada Shopify Hardware Store
The United States Shopify Hardware Store
The United Kingdom Shopify Hardware Store
Ireland Shopify Hardware Store
Europe SocketStore.eu
Japan SocketStore.jp

Pair and connect your barcode scanner with your iPad

  1. Go to your iPad settings (not the app settings) and make sure that Bluetooth is turned on.

  2. Turn on the barcode scanner by holding down the power button until the scanner beeps.

  3. From Shopify POS, tap > Settings.

  4. Tap Set up hardware > Barcode scanner.

  5. When the Enable pairing mode dialog appears, scan the barcode. The scanner beeps three times when pairing mode is enabled.

  6. Tap View available devices.

  7. To pair and connect the barcode scanner, tap it when it appears in the Select An Accessory dialog (you might have to wait a few moments).

If the setup is not successful, then unpair the scanner and try again.

As long as the scanner remains paired with the iPad, the scanner connects automatically whenever it's in range.

Pair with another iPad or a different Bluetooth device

You can pair your scanner with another iPad or Bluetooth device.

Steps:

  1. Unpair the barcode scanner.

  2. Pair your scanner with another iPad, or read the manufacturer's instructions to pair with a different Bluetooth device.

Unpair your barcode scanner

By default, your barcode scanner tries to connect to the last device that it was paired with. If you want to use your barcode scanner with a different Bluetooth device, then you need to unpair the scanner and iPad first.

Steps:

  1. Turn on your barcode scanner.

  2. Press and hold the scan button. At the same time, press and hold the power button. When you hear three beeps, release both buttons. Your barcode scanner powers off.

  3. From Shopify POS, tap > Settings.

  4. Tap Manage connected hardware.

  5. Tap the name of your connected barcode scanner.

  6. Tap Forget scanner.

  7. Go to your iPad's settings (not the app settings).

  8. Tap Bluetooth.

  9. Under MY DEVICES, tap the button beside the Socket barcode scanner.

  10. Tap Forget This Device.

  11. Tap Forget Device.

Troubleshoot the 1D barcode scanner

If you're having trouble scanning barcodes with Shopify POS and the Socket Mobile S700 or CHS 7Ci barcode scanner, then try these troubleshooting steps to fix the problem:

Check your scanner setup

  1. Are you using the correct barcode scanner? The only 1D barcode scanners that Shopify POS supports are the Socket Mobile S700 and CHS 7Ci.

  2. Are you using the barcode scanner with an iPad? The barcode scanner doesn't work with Shopify POS for iPhone or Android.

  3. Is the scanner charged and in range of the iPad? Check that the scanner is fully charged and within range (100 meters or less).

  4. What type of barcode are you scanning? This scanner works only with 1D barcodes. Make sure that you're using a supported barcode type.

Check that your scanner and iPad are paired correctly

  1. Is the barcode scanner showing as Connected on the Shopify POS Hardware settings screen when the scanner is on and in range? If not, then go to your iPad's Bluetooth settings and forget the barcode scanner, and pair it with your iPad again.

  2. Is the scanner showing in your iPad's Bluetooth settings? Make sure that the iPad's Bluetooth is enabled and the scanner shows as Connected.

  3. When you paired the scanner and iPad, did you scan the correct barcode in Shopify POS? The 1D barcode sets the barcode scanner to iOS mode to work with your iPad. If you didn't hear the three beeps when you scanned the barcode, or if you accidentally scanned the 2D barcode, then the scanner isn't in iOS mode. Unpair it and the iPad, and then pair them again, making sure that you scan the 1D barcode in Shopify POS and hear the three beeps before you move on to the next step.

  4. Was the scanner paired with another iPad? The scanner can be paired with only one iPad at a time. Unpair the scanner and the other iPad, and then pair the scanner with the new iPad.

  5. Do you have a poor Bluetooth connection? Read Apple's advice on reducing Bluetooth interference.

Check your products' barcodes

  1. Does the scanner recognize any barcodes? Try scanning the barcode of a nearby item that isn't one of your store's products. If your scanner is paired correctly, then you should see an Unrecognized barcode error in Shopify POS. If you see this error, then carry on to the next steps. If you don't see an error, then unpair the scanner and iPad, and pair them again.

  2. Is the product visible on Shopify POS? If the product's hidden on Shopify POS, then scanning its barcode doesn't work because the app didn't load the product. If you see an Unrecognized barcode error, then check the product's availability settings in your Shopify admin.

  3. Does the barcode number on the label match the product's barcode number in your Shopify admin? If there are extra zeros at the beginning or end of the number, then delete them and try again.

Trying to scan in inventory with the barcode scanner?

You can't scan in inventory with Shopify POS. The barcode scanner is for quickly adding products to the cart before checkout.

Supported barcode types

The Socket Mobile S700 and CHS 7Ci barcode scanners support the following 1D barcode types:

  • Bookland EAN
  • Chinese 2 of 5
  • Codabar (including ISBT 128 bit concatenation)
  • Code 11, Code 128
  • Code 39
  • Trioptic Code 39
  • Code 39 Full ASCII
  • Code 93
  • Discrete 2 of 5
  • GS1 DataBar (RSS)
  • GS1-128 (UCC-128/EAN-128)
  • ISBN
  • ISBT 128
  • Interleaved 2 of 5 (ITF-14)
  • MSI
  • Standard 2 of 5
  • Telepen
  • UPC/EAN (UPC-A, UPC-E, UPC-E1, EAN-13, EAN-8, UCC/EAN-128)
  • VIN

Factory reset

If the troubleshooting steps don't work and you still have trouble with the Socket Mobile S700 or CHS 7Ci barcode scanner, then you can try resetting the scanner to its factory settings.

Steps:

  1. Make sure that the scanner and iPad are unpaired.

  2. Power the barcode scanner back on.

  3. Scan the factory reset barcode from the manufacturer's user manual:

  4. Pair the scanner and iPad again.

Ready to start selling with Shopify?

Try it free